There is a version of DStv Installation that takes forty minutes and a version that takes ninety, and the difference is almost entirely in the parts nobody sees. Cable clipped and weatherproofed rather than draped over a gutter. A wall bracket bolted into brick rather than into mortar joints. An LNB skewed for Sandton's longitude instead of left at whatever angle it came out of the box. Grounding, where the installation warrants it.
Ours is the longer version, because the forty-minute version is what generates the callback in November when the first proper storm arrives. It is cheaper for everyone to do it once.
On alignment specifically: we use a satellite meter, not the decoder's on-screen bar. The on-screen reading is coarse enough that a dish can show a usable signal while sitting well off the true peak — which is exactly the installation that fails in rain, because it has no margin left to lose. A properly peaked dish has headroom, and headroom is what keeps the picture up when the weather closes in.
We show you the meter figures at the end, so you have a baseline. If the signal ever drops, you will know what it used to be — and that single fact makes the next diagnosis far quicker, whoever does it. Free assessment, fixed quote, 12-month workmanship warranty. 069 423 8290.
Guesthouses, sports bars, lodges and waiting rooms run on different rules to a household — commercial subscriptions, multiple decoders and often a distribution system feeding a dozen screens. We do that work too, and it is worth scoping properly rather than treating it as a big domestic install.
Rain fade, storms and the signal in Gauteng
If you lose the picture during a highveld thunderstorm and it comes back afterwards, that is rain fade, and it is physics rather than a fault. Ku-band satellite signal is absorbed by heavy rain between your dish and the satellite. Every dish in Gauteng does it to some degree. The question is how much margin your installation has before it gives up.
Margin is what separates a good install from a bad one. A dish peaked properly on a meter might sit at a signal quality reading in the high seventies on a clear day; the same dish aligned by eye might read in the low sixties and look identical on screen. When a storm takes fifteen points off both, one keeps showing a picture and the other goes to E48-32. Same dish, same decoder, same weather — different install.
What we can do about it. Peak the dish properly. Check the LNB skew, which is frequently left wrong and quietly costs several points. Replace corroded connectors and any cable that has been sun-baked to the point of loss. Where a property genuinely sits in a difficult spot, a larger dish buys back real margin.
What nobody can do about it. Eliminate it entirely. Anyone promising a system that never drops in a cloudburst is selling something. We would rather be straight about it.
On dish size specifically: stepping up from a 60cm to a 90cm reflector typically buys a few decibels of margin, which in practice is the difference between losing the picture in a heavy shower and riding through it. It is not the answer for every property, but where rain fade is a chronic complaint it is usually the most cost-effective fix available.
DStv work across Sandton
Working Sandton regularly means the awkward parts of a satellite job stop being surprises. Across Morningside, Bryanston, Rivonia and Illovo we already know which roofs are tile and which are IBR sheeting, which complexes have body-corporate rules about dishes on street-facing elevations, and which streets have mature trees on the northern side that will grow into the signal path within two summers.
Line of sight is the whole job. DStv comes off Intelsat 20, which from Sandton sits low in the northern sky. That means anything tall to the north — a neighbour's roof, a jacaranda, a new double-storey next door — can block a dish that worked perfectly for years. When someone tells us reception died and nothing changed, a tree having grown is very often what changed.
Mounting matters more than people think. A dish is a sail. On a tile roof it wants a proper tile-bracket rather than a bolt through the batten; on a wall it wants brick, not the mortar course. We would rather spend ten minutes finding a solid fixing than come back in a year to realign something that has crept.
Access is worth flagging when you book: if the dish is on a double-storey, above a pitched roof, or behind a locked roof hatch, say so. It changes what we bring and it is the difference between a job finished today and a second visit.
If you are in a complex or sectional-title scheme, check whether there is already a communal dish and distribution before paying for anything. A surprising number of new installations get sold into buildings that already had a feed available in the roof space, and connecting to that is dramatically cheaper than putting up your own.
What the error codes actually mean
The codes on screen are more useful than they look, and knowing which family yours belongs to tells you whether you need a technician at all.
E48-32 — "no signal being received". The one everyone knows. The decoder is not seeing usable signal from the dish. Causes run from weather, through a shifted dish or dead LNB, to a cable fault. If it clears when the rain stops, your installation is marginal rather than broken. If it does not clear, something in the chain has failed.
E16 and subscription-family codes. The decoder is receiving fine and is not authorised to decrypt. This is an account or smartcard matter, not a dish one. Clearing an error on the self-service portal fixes most of these in minutes, and it costs nothing.
E30-4 and similar. Usually a decoder that has lost part of its channel or authorisation data. Frequently recoverable with a proper reset rather than a replacement.
No code, no picture, no lights. Power supply, and often the simplest fix in the whole list.
Have the code to hand when you phone — 069 423 8290. It genuinely changes what we bring and occasionally means we can tell you over the phone that you do not need us at all, which is a better outcome than a call-out fee for a subscription problem.
Before booking anyone for an error code, it is worth trying the DStv self-service portal — clearing an error there resolves a good share of subscription-family codes in a couple of minutes, free. If that does not fix it, the fault is genuinely technical and worth a visit. We would rather you tried the free option first.
How a DStv Installation job runs
Five steps, and you know where you are at each one.
1. The call. You describe the symptom — the error code, whether it happens in rain, whether anything was installed or trimmed recently. That is usually enough to know whether we are bringing an LNB, a length of cable, or a meter and a ladder.
2. The assessment. Free. We read the signal quality and strength at the decoder first, because that single reading splits the whole diagnosis in two: healthy signal means the problem is the decoder, smartcard or subscription; poor signal means it is the dish, LNB or cable. Skipping this step is how people end up paying for realignment they never needed.
3. The quote. One fixed number for the confirmed fault. Approved by you before anything is touched, and it does not move afterwards.
4. The work. On-site, almost always in one visit. Alignment on a satellite meter rather than the on-screen bar, connectors made up fresh rather than reused, and anything exposed weatherproofed properly.
5. The handover. We show you the final signal readings and run through the channels you actually watch, not just the first one in the list. Cover begins from that point — 12-month on workmanship.
Payment on completion, after the system is working in front of you.
You get an invoice listing the work, the parts fitted and the final signal readings. Keep it. Those readings are the single most useful thing anyone can have when reception changes years later, because they establish what the installation was capable of when it was healthy.
If a part has to be ordered rather than coming off the van, you get a real date rather than an optimistic one — including when that date is inconvenient. An honest delay is easier to plan around than a promise that quietly slips twice.
Where the money goes on a dish job
Three things make up a satellite invoice: parts, the labour to fit them, and the time spent working out which parts were actually needed. Knowing the split makes a fair quote easy to recognise.
Parts. Dishes, LNBs, brackets, coax and connectors are not expensive items individually, and the difference between adequate and good is small in rand terms. Which is exactly why cutting corners here makes no sense — a few rand saved on cable buys you a re-cable in three years.
Labour. Most of it is access and alignment. Getting safely onto a double-storey pitched roof takes longer than the work itself, and peaking a dish properly on a meter takes longer than swinging it until the on-screen bar goes green. Both are worth paying for.
Diagnosis. Free here, but it is real work, and it is what stops you buying a new dish when you needed a new connector.
Where not to economise. Cheap unshielded coax, reused weathered F-connectors, brackets fixed into mortar rather than brick, and skipping weatherproofing on an outdoor joint. Every one of those is a callback waiting to happen, usually during the worst weather of the year, along with everyone else's.
If a lightning strike took out the LNB and decoder together, ask for a written assessment. Most household policies cover surge and strike damage to electronics, and an insurer generally wants a technician's description of which components failed and why. Writing it up costs you nothing and is often worth considerably more than the repair.
If you need the quote in writing for a landlord, a body corporate or an insurer, we will provide it itemised properly rather than as a single figure on a slip. A one-line quote tends to come straight back with questions, and that wastes a fortnight for everybody.
Dishes, LNBs and the parts that matter
A satellite installation is four components and a cable, and each one has a version that lasts and a version that does not.
The dish. Most homes in Sandton are fine on a standard offset dish. Bigger is not automatically better, but where a property sits in a marginal spot — heavy tree cover, a long way from the beam centre, chronic rain-fade complaints — a larger reflector buys real margin and is usually the cheapest way to buy it. What matters more than size is that the reflector is not dented and the mount is rigid.
The LNB. This is the part that fails. It sits outdoors in full sun and takes every induced surge the weather offers. A single-output LNB feeds one decoder; a twin feeds two independently; a SMART LNB is what a modern Extra View setup expects. Fitting the wrong type is a common cause of "the second room never worked properly".
The cable. Proper satellite-grade coax, run in one length where possible, with compression connectors rather than the push-on kind. Joins in a cable run are where water gets in.
The decoder. Explora, Explora Ultra or a standard HD unit — which you want depends on your viewing, and we will say plainly when the cheaper one does everything you need.
On Extra View specifically: linking a second decoder properly needs either a SMART LNB or the right splitter arrangement, plus a cable path to the second room. Done correctly it is invisible; done with the wrong LNB it produces a second room that half works and drops channels at random, which is one of the more common faults we are called out to undo.
Where an existing installation is sound, we will say so and reuse it. Plenty of call-outs end with a new LNB on a perfectly good ten-year-old dish, because the reflector is a piece of shaped metal and there is nothing about it that wears out if the mount is solid.
We will tell you when it is not the dish
A decent share of satellite call-outs are not satellite faults, and saying so costs us the job. We say so anyway, for the same reason any trade that intends to still be here in ten years does.
Subscription and account errors. If the signal reading is healthy and you are still getting an error, no work on the dish will change anything. Most of these clear from the self-service portal in a few minutes at no cost. We will talk you through it rather than book a call-out.
HDMI, TV input and sound problems. A decoder working perfectly into a television set to the wrong input looks exactly like a dead decoder. So does a failed HDMI cable. Both get checked before anyone goes near the roof.
Faults that are actually the television. Occasionally the decoder and signal are fine and the set itself has a problem — which, as it happens, we also fix.
Weather. If it drops in heavy rain and returns afterwards, and the margin measures healthy, that is rain fade rather than a fault. We will tell you what could improve it and what genuinely cannot. No charge for being told.
Second opinions are welcome, including on our own findings. If someone has quoted you for a new dish and it does not feel right, describe what they told you — more than once we have found a healthy signal reading behind a quote for a full reinstallation. The assessment is free either way, and we have talked people into accepting a competitor's quote before now.
The same applies in reverse: if the fault genuinely is the dish and someone has told you it is the decoder, we will say that too. The point is not to talk you out of work, it is to make sure the money goes where the fault actually is.
Why Sandton calls us for satellite work
Nothing dramatic — just the things that ought to be normal and frequently are not.
We read the signal before we sell anything. Signal quality and strength at the decoder, first, every time. It costs two minutes and it is the difference between fixing your fault and selling you a realignment you did not need.
Alignment is done on a meter. Not the on-screen bar. A dish peaked properly has margin left for weather; one swung until the bar turns green often does not, which is why it fails in the first storm after the visit.
The quote is fixed before work starts. Approved by you, unchanged afterwards. If the job turns out harder than judged, that is ours to absorb.
We will tell you when it is not our problem. Subscription errors, smartcard issues and account authorisations are DStv's to fix, they cost you nothing, and sending you to the self-service portal loses us a call-out fee. We do it anyway.
Same technician, start to finish. Thabo Mokoena and the team assess and return to fit, so nobody re-learns your roof from scratch.
Trade and business customers get the same terms with a bit more structure — scheduled attendance around trading hours, consolidated invoicing, and one point of contact rather than starting a fresh conversation each time. Estates, guesthouses and hospitality venues make up a decent share of the satellite work we do.
You will also hear from us when something changes. If a part is delayed or the schedule slips, you get told the day before rather than at the appointment time. It sounds minor until you have taken a morning off work for a visit that was never going to happen.
Our guarantee on DStv Installation
Short enough to read, specific enough to hold us to.
The assessment is free. Whether or not you proceed, and regardless of what we find. No call-out fee that appears afterwards. If the answer is that your fault is a subscription matter DStv will clear for nothing, you will be told that and you will owe us nothing for it.
The quote is fixed. Approved by you before anything is touched, and unchanged afterwards. A genuinely separate second fault means a phone call and a fresh decision, never a surprise line on the invoice.
The work is warranted for 12-month. On workmanship — alignment holding, connectors staying watertight, cable runs staying intact. Parts carry their own cover on top of that.
You see the signal readings. Quality and strength, at handover, so you have a documented baseline. If reception ever changes you will know what it used to be, and that makes every future diagnosis faster.
You pay on completion. After the system is working in front of you. No deposit, no staged payments.
That is the entire arrangement, which is why the fine print on our quotes runs to about four lines.
The warranty follows the installation rather than you, so if you sell the property inside the cover period the new owner inherits whatever remains of it. Leave the invoice with the house. It costs us very little, because work done properly does not generate claims.
Nothing in that list depends on you keeping paperwork. We hold the job record ourselves, so a phone call with your address and a rough date is enough for us to find what was done and pick the conversation up from there.
DStv Installation in Sandton — common questions
Can you fix a cracked or smashed screen?
Sometimes, and we'll give you an honest cost comparison before you commit. Screen panels are by far the most expensive single component in a TV, so on a large or older set, the repair cost can approach the price of an equivalent new TV — in which case we'll say so plainly. On smaller or newer sets, panel replacement is often genuinely worthwhile.
Do you service Illovo, Rivonia, Bryanston and Morningside?
Yes — Sandton and its surrounds including Morningside, Bryanston, Rivonia and Illovo are part of our standing coverage, with Thabo Mokoena in the area regularly. If you're just outside the listed suburbs, call 069 423 8290 anyway; listed areas are our patches, not our limits.
My TV won't turn on at all — what's usually wrong?
In the large majority of cases, a failed power supply board or worn-out capacitors — one of the most common and most affordable TV repairs there is. A telltale sign is a faint click or pop when you try to switch it on. We test the board properly before quoting, since a small number of "won't turn on" cases are actually a mainboard fault instead.
My smart TV apps keep crashing or Wi-Fi won't connect — is that a hardware fault?
Usually not. Most smart-platform faults — crashing apps, frozen menus, Wi-Fi that won't hold — are software issues: full storage, corrupted app data or outdated firmware. We try the free software fixes first (cache clearing, firmware updates, a careful factory reset) before treating it as a hardware fault.
What information should I have ready when I call?
The brand and approximate screen size, roughly how old the TV is, and what it's actually doing (or not doing) — a black screen with sound still playing is a very different fault from a TV that's completely dead. A photo or short video sent on WhatsApp helps us prepare and often speeds up the diagnosis.
Do you repair TVs you didn't sell or previously service?
All the time — most of our Sandton work is TVs bought from a retailer, not from us. We diagnose with proper test equipment, quote the fix fixed, and repair every major brand. You don't need any prior relationship with us to get a fair diagnosis and quote.
What is the free diagnosis, exactly?
A proper fault-finding assessment using real test equipment — power measured under load, the panel and backlight checked independently, ports and connectors tested — to identify the actual failed component rather than guess. You get a plain-language explanation of what's wrong and a fixed quote to fix it, with no obligation to proceed through us.
Which TV brands do you repair?
All major brands, including Samsung QLED, Sony BRAVIA and LG OLED sets — we're not tied to any manufacturer, so the advice on repair vs replace is based on your specific TV, not on what we happen to stock. See our brand guides at /brands/ for what we know about each manufacturer's common fault patterns.