Most calls about DStv Dish Alignment in Midrand start the same way: it worked, and now it doesn't, and nobody has touched anything. That is almost always true — satellite systems fail on their own, gradually, through weather and corrosion and the slow drift of a mount that was never quite tight enough.
The causes are mundane. Water tracking down the coax into an F-connector. An LNB that has taken one lightning-season surge too many. A dish that has shifted a degree or two because the bracket bolts were snug rather than torqued. A decoder that lost its authorisation and needs a proper reset rather than another plug-out-plug-in. None of these need a new installation — they need someone to work out which one it is before selling you anything.
So that is what happens first, and it costs nothing. We check the signal at the decoder, then at the LNB, then look at the dish itself, and tell you which part of the chain has failed. Then you get one fixed price to put it right, and it doesn't move once you have approved it.
The 12-month workmanship warranty stands on all of it and the system is tested properly before we leave — not a single channel for ten seconds, but a run through the signal meter and a look at the transponders that carry the channels you actually watch. 069 423 8290 to book, or describe the fault and we will tell you what it points to.
If you are thinking about a second or third room while we are there, mention it at booking rather than afterwards. Running the extra cable during the original visit is a fraction of what it costs to come back and do it later, and it determines which LNB should go up in the first place.
Rain fade, storms and the signal in Gauteng
If you lose the picture during a highveld thunderstorm and it comes back afterwards, that is rain fade, and it is physics rather than a fault. Ku-band satellite signal is absorbed by heavy rain between your dish and the satellite. Every dish in Gauteng does it to some degree. The question is how much margin your installation has before it gives up.
Margin is what separates a good install from a bad one. A dish peaked properly on a meter might sit at a signal quality reading in the high seventies on a clear day; the same dish aligned by eye might read in the low sixties and look identical on screen. When a storm takes fifteen points off both, one keeps showing a picture and the other goes to E48-32. Same dish, same decoder, same weather — different install.
What we can do about it. Peak the dish properly. Check the LNB skew, which is frequently left wrong and quietly costs several points. Replace corroded connectors and any cable that has been sun-baked to the point of loss. Where a property genuinely sits in a difficult spot, a larger dish buys back real margin.
What nobody can do about it. Eliminate it entirely. Anyone promising a system that never drops in a cloudburst is selling something. Honest expectation setting beats a callback.
On dish size specifically: stepping up from a 60cm to a 90cm reflector typically buys a few decibels of margin, which in practice is the difference between losing the picture in a heavy shower and riding through it. It is not the answer for every property, but where rain fade is a chronic complaint it is usually the most cost-effective fix available.
DStv work across Midrand
Working Midrand regularly means the awkward parts of a satellite job stop being surprises. Across Noordwyk, Vorna Valley, Kyalami and Halfway Gardens we already know which roofs are tile and which are IBR sheeting, which complexes have body-corporate rules about dishes on street-facing elevations, and which streets have mature trees on the northern side that will grow into the signal path within two summers.
Line of sight is the whole job. DStv comes off Intelsat 20, which from Midrand sits low in the northern sky. That means anything tall to the north — a neighbour's roof, a jacaranda, a new double-storey next door — can block a dish that worked perfectly for years. When someone tells us reception died and nothing changed, a tree having grown is very often what changed.
Mounting matters more than people think. A dish is a sail. On a tile roof it wants a proper tile-bracket rather than a bolt through the batten; on a wall it wants brick, not the mortar course. We would rather spend ten minutes finding a solid fixing than come back in a year to realign something that has crept.
Tell us this when you call: if the dish is on a double-storey, above a pitched roof, or behind a locked roof hatch, say so. It changes what we bring and it is the difference between a job finished today and a second visit.
If you are in a complex or sectional-title scheme, check whether there is already a communal dish and distribution before paying for anything. A surprising number of new installations get sold into buildings that already had a feed available in the roof space, and connecting to that is dramatically cheaper than putting up your own.
The signal faults we see most in Midrand
Satellite systems fail in a fairly small number of ways, and the symptom usually narrows it down before anyone climbs onto a roof.
- No signal, all channels, all weather. Dish moved, LNB dead, or cable open somewhere. If it happened after wind, suspect the mount; after lightning, suspect the LNB.
- Signal fine on clear days, gone in rain. The install has no margin. Alignment is off-peak, or the LNB skew is wrong, or the cable run has gone lossy.
- Some channels, not others. Almost always a polarity or band problem — a failing LNB, or a decoder that has lost its LNB control voltage.
- Picture breaks into blocks intermittently. Marginal signal, or water in a connector. Water is the more common of the two and the cheaper to fix.
- Error codes with a full signal reading. Not a dish fault at all. That is subscription, smartcard or decoder authorisation, and no amount of realignment will help.
The last one is worth dwelling on, because it is where people get charged for work they never needed. If the signal quality reading is healthy and you are still getting an error, the problem is downstream of the dish. We take that reading before anything else — and if it is fine, we will tell you the fix is a phone call to DStv rather than a bill from us.
Intermittent faults are the hardest to catch, so anything you can tell us about the pattern is worth more than it sounds — whether it happens at a particular time of day, only in wind, only when it is hot. If you can note the signal quality reading from the decoder's information screen while the fault is happening, that alone often identifies the cause.
How a DStv Dish Alignment job runs
Five steps, and you know where you are at each one.
1. The call. You describe the symptom — the error code, whether it happens in rain, whether anything was installed or trimmed recently. That is usually enough to know whether we are bringing an LNB, a length of cable, or a meter and a ladder.
2. The assessment. Free. We read the signal quality and strength at the decoder first, because that single reading splits the whole diagnosis in two: healthy signal means the problem is the decoder, smartcard or subscription; poor signal means it is the dish, LNB or cable. Skipping this step is how people end up paying for realignment they never needed.
3. The quote. One fixed number for the confirmed fault. Approved by you before anything is touched, and it does not move afterwards.
4. The work. On-site, almost always in one visit. Alignment on a satellite meter rather than the on-screen bar, connectors made up fresh rather than reused, and anything exposed weatherproofed properly.
5. The handover. We show you the final signal readings and run through the channels you actually watch, not just the first one in the list. Cover begins from that point — 12-month on workmanship.
Payment on completion, after the system is working in front of you.
You get an invoice listing the work, the parts fitted and the final signal readings. Keep it. Those readings are the single most useful thing anyone can have when reception changes years later, because they establish what the installation was capable of when it was healthy.
If a part has to be ordered rather than coming off the van, you get a real date rather than an optimistic one — including when that date is inconvenient. An honest delay is easier to plan around than a promise that quietly slips twice.
Where the money goes on a dish job
Three things make up a satellite invoice: parts, the labour to fit them, and the time spent working out which parts were actually needed. Knowing the split makes a fair quote easy to recognise.
Parts. Dishes, LNBs, brackets, coax and connectors are not expensive items individually, and the difference between adequate and good is small in rand terms. Which is exactly why cutting corners here makes no sense — a few rand saved on cable buys you a re-cable in three years.
Labour. Most of it is access and alignment. Getting safely onto a double-storey pitched roof takes longer than the work itself, and peaking a dish properly on a meter takes longer than swinging it until the on-screen bar goes green. Both are worth paying for.
Diagnosis. Free here, but it is real work, and it is what stops you buying a new dish when you needed a new connector.
Where not to economise. Cheap unshielded coax, reused weathered F-connectors, brackets fixed into mortar rather than brick, and skipping weatherproofing on an outdoor joint. All four come back, usually during the worst weather of the year, along with everyone else's.
If a lightning strike took out the LNB and decoder together, ask for a written assessment. Most household policies cover surge and strike damage to electronics, and an insurer generally wants a technician's description of which components failed and why. Writing it up costs you nothing and is often worth considerably more than the repair.
If you need the quote in writing for a landlord, a body corporate or an insurer, we will provide it itemised properly rather than as a single figure on a slip. A one-line quote tends to come straight back with questions, and that wastes a fortnight for everybody.
Genuine, generic, and where the difference shows
Not every part needs to be branded, and anyone insisting otherwise is padding the invoice. The honest breakdown:
Where it matters. The LNB, and the decoder. LNBs vary enormously in noise figure and in how well they survive a few summers outdoors; a cheap one measurably costs you signal margin from the day it goes up, and fails sooner. Decoders should be genuine, full stop — the authorisation and smartcard handling is not something to gamble on.
Where generic is completely fine. Brackets, wall mounts, cable clips, weatherproofing tape. A bracket is a bent piece of steel; what matters is that it is galvanised and bolted into something solid.
Where the label is irrelevant but the spec is not. Coax. Nobody needs branded cable, but it does need to be genuine satellite-grade with a proper copper centre conductor and decent shielding. The very cheap stuff sold as satellite cable often has a copper-clad steel core that loses noticeably more signal over a long run.
We tell you what we fitted, either way — make and type, not just "LNB replaced". That record is worth having, and it settles any later question about whether the part needed changing at all.
Ask us to leave whatever we remove. A corroded LNB or a length of cable with a green connector at the end tells you more about why the system failed than any invoice line can, and it settles the question of whether the part genuinely needed replacing.
If you would prefer branded parts on something where we would normally fit a good generic, that is entirely your call and we will price it both ways. What we will not do is fit something we expect to fail and warrant it anyway.
Done once, properly
The measure of a satellite installation is not whether it works on the day. Every installation works on the day. The measure is whether it still works, unattended, through three summers of storms and sun.
What that takes. Mounts bolted into structure rather than into mortar or battens. Cable clipped at proper intervals so wind cannot work it loose, with a drip loop before it enters the wall so water runs off rather than in. Compression connectors, made up fresh. Outdoor joints weatherproofed. LNB skew set for Midrand rather than left at the factory angle. And the dish peaked on a meter with the readings recorded.
What it costs. An extra half hour, most of the time. That is the entire difference, and it is why we would rather quote honestly for the longer job than win the work and be back in eighteen months.
You notice this by its absence — no pixelation in ordinary rain, no gradual decline over a season, no call-out the week after the first big storm. That is the thing being sold here, and it does not photograph well, which is presumably why so much of the trade skips it.
Everything gets recorded: dish size and position, LNB type, cable route, decoder model and the signal readings at handover. That record lives with us, so if you call in three years about a change in reception the conversation starts from what was actually installed rather than from guesswork on a roof.
None of this is unusual or clever. It is simply the version of the job that a competent installer would do if nobody were watching, which is the only definition of the trade that means anything.
We will tell you when it is not the dish
A decent share of satellite call-outs are not satellite faults, and saying so costs us the job. We say so anyway, for the same reason any trade that intends to still be here in ten years does.
Subscription and account errors. If the signal reading is healthy and you are still getting an error, no work on the dish will change anything. Most of these clear from the self-service portal in a few minutes at no cost. That is a phone conversation, not a visit.
HDMI, TV input and sound problems. A decoder working perfectly into a television set to the wrong input looks exactly like a dead decoder. So does a failed HDMI cable. Both get checked before anyone goes near the roof.
Faults that are actually the television. Occasionally the decoder and signal are fine and the set itself has a problem — which, as it happens, we also fix.
Weather. If it drops in heavy rain and returns afterwards, and the margin measures healthy, that is rain fade rather than a fault. We will tell you what could improve it and what genuinely cannot. You owe nothing for that answer.
Second opinions are welcome, including on our own findings. If someone has quoted you for a new dish and it does not feel right, describe what they told you — more than once we have found a healthy signal reading behind a quote for a full reinstallation. The assessment is free either way, and we have talked people into accepting a competitor's quote before now.
The same applies in reverse: if the fault genuinely is the dish and someone has told you it is the decoder, we will say that too. The point is not to talk you out of work, it is to make sure the money goes where the fault actually is.
If the signal drops again
Outdoor equipment fails. Connectors let water in, LNBs take surges, and mounts occasionally move in wind that nobody expected. Any installer claiming otherwise has not been doing it long. What matters is what happens next.
Report it and it is triaged the same day. Phone 069 423 8290, tell us roughly when we were out, and you get an answer that day. We keep the job record — what was fitted, what the signal read at handover — so the conversation starts from facts rather than from your description of work you did not do.
If it is our workmanship, it is free. Alignment that has drifted, a connector we made up that has let water in, cable we ran that has come loose — inside the 12-month window that is our return visit and our fix, with no argument about whether it is really the same fault.
If it is weather or a new fault, we say so and quote it fresh. A dish that survived three seasons and then took a lightning hit has not had a failed installation. You get a free diagnosis on the new fault and a fixed quote before anything is touched.
Where the fix is on DStv's side, it costs you nothing here — the arrangement does not change.
Response times, plainly: a warranty issue reported on a working day gets an answer that day and attendance within the next couple of days across the areas we cover. Storm weeks are the exception and we will say so honestly rather than book a slot we already know we will have to move.
And if a repeat fault turns out to be something we could reasonably have caught the first time, we will say so plainly rather than reaching for the fine print. That happens occasionally to everyone in this trade; pretending otherwise is what costs a business its reputation.
DStv Dish Alignment in Midrand — common questions
What information should I have ready when I call?
The brand and approximate screen size, roughly how old the TV is, and what it's actually doing (or not doing) — a black screen with sound still playing is a very different fault from a TV that's completely dead. A photo or short video sent on WhatsApp helps us prepare and often speeds up the diagnosis.
Do you service Vorna Valley, Noordwyk, Kyalami and Halfway Gardens?
Yes — Midrand and its surrounds including Noordwyk, Vorna Valley, Kyalami and Halfway Gardens are part of our standing coverage, with Thabo Mokoena in the area regularly. If you're just outside the listed suburbs, call 069 423 8290 anyway; listed areas are our patches, not our limits.
Which TV brands do you repair?
All major brands, including Samsung and LG LED/QLED sets, growing Hisense Mini-LED numbers — we're not tied to any manufacturer, so the advice on repair vs replace is based on your specific TV, not on what we happen to stock. See our brand guides at /brands/ for what we know about each manufacturer's common fault patterns.
Do you use genuine or compatible parts?
Both, depending on the component — and we'll tell you which one you're getting. Power boards, capacitors and HDMI connectors have a mature, reliable compatible-parts market we use confidently. Screen panels and mainboards lean toward genuine or manufacturer-matched parts, where compatibility matters more. Either way, every part carries our 12-month workmanship warranty.
My smart TV apps keep crashing or Wi-Fi won't connect — is that a hardware fault?
Usually not. Most smart-platform faults — crashing apps, frozen menus, Wi-Fi that won't hold — are software issues: full storage, corrupted app data or outdated firmware. We try the free software fixes first (cache clearing, firmware updates, a careful factory reset) before treating it as a hardware fault.
What does the 12-month warranty cover?
The repair we performed: the part we fitted and the labour to fit it. If the specific fault we fixed comes back within the warranty period, we return and repair it free — one phone call, no forms. It doesn't cover a new, unrelated fault developing afterward, which we'd diagnose and quote separately.
What is the free diagnosis, exactly?
A proper fault-finding assessment using real test equipment — power measured under load, the panel and backlight checked independently, ports and connectors tested — to identify the actual failed component rather than guess. You get a plain-language explanation of what's wrong and a fixed quote to fix it, with no obligation to proceed through us.
Do you offer on-site repairs, or do I need to bring the TV in?
Both — whichever suits you and the fault. Many faults (power boards, HDMI ports, sound issues, software faults) can be diagnosed and often fixed on-site. Screen replacements and some mainboard repairs are usually better handled at the workshop, and we can collect and deliver if that's easier for you. We'll recommend the right option once we know the symptom.